TiAlZr合金微动磨损性能研究

采用高精度液压式微动磨损试验机研究了TiA lZr合金在不同微动运行区域的微动磨损行为,建立了其运行工况微动图。试验结果表明:滑移区、混合区和部分滑移区的摩擦因数随循环次数变化呈现不同的规律,其中部分滑移区摩擦因数较低,磨损体积随着位移幅值的增大而增大;滑移区、混合区磨损体积随着法向载荷的增加而增大,而部分滑移区磨损体积随着法向载荷的增加而减小;滑移区磨屑堆积于中心区域,磨损以磨粒磨损和剥层机制为主;混合区磨损机制主要表现为粘着磨损与磨粒磨损并存;部分滑移区磨损轻微。     

纳米锌填充超高分子量聚乙烯复合材料微动摩擦磨损性能

利用热压烧结法制备不同含量纳米锌填充超高分子量聚乙烯(UHMWPE)复合材料,采用微动摩擦磨损试验机研究干摩擦条件下纳米锌含量对复合材料微动摩擦磨损性能的影响。利用场发射扫描电子显微对复合材料断面进行分析,采用扫描电子显微镜对材料磨损表面及钢球进行表征,探讨复合材料的磨损机制。研究结果表明:随着纳米Zn含量的增加,复合材料的摩擦因数和磨损率均表现为先降低后升高;当纳米Zn质量分数为1%时复合材料具有最低的摩擦因数和磨损率,且对偶钢球表面形成连续的转移膜;复合材料的磨损机制主要为黏着磨损和磨粒磨损。添加锌纳米颗粒,可以提高UHMWPE复合材料的微动摩擦磨损性能,当纳米锌质量分数为1%时,复合材料具有最低的摩擦因数和最优的耐磨损性能。     

钛合金燕尾榫结构在不同疲劳载荷下的断口分析

对TC11钛合金燕尾榫连接结构在低周和高低周复合载荷作用下的断口特征进行了分析.结果表明:在微动环境下,微动磨损面上有表面金属掉块和不均匀的磨损擦伤,磨损表面出现腐蚀坑以及损伤区呈现层状及山丘状的塑性变形;在高低周复合载荷情况下,疲劳源处疲劳辉纹呈现以河流花样为主的复杂疲劳条纹,在裂纹扩展阶段,河流花样比较杂乱,裂纹扩展方向相对无序,每个低周周期中的疲劳台阶也不明显.     

弹性联轴器对柴油机输出转矩不均匀性衰减研究

从理论和试验两方面，研究四种弹性联轴器对柴油机输出转矩不均匀性的衰减效果及衰减规律。主要分析联轴器的扭转刚度和输入转速对柴油机输出转矩不均匀性的影响，为选择和改进弹性联轴器提供科学依据。     

齿轮减速器扭振特性实验辨识及简化动力模型研究

本文通过对二级齿轮减速器扭振特性的实验测定，识别了系统的动力学参数。在此基础上提出用三质量弹簧简化模型代表复杂齿轮减速器的方法，并对简化模型的特性参数进行了辨识，为齿轮传动系统的动力学分析，提供了一种有效的分析方法。     

Influence of content of carbon fabric on the low amplitude oscillating wear performance of polyetherimide composites

Tribo-potential of bi-directionally (BD) reinforced polymer composites is not yet adequately explored especially in low amplitude oscillating wear (LAOW)/fretting wear mode. Hence five composites of Polyetherimide (PEI) containing carbon fabric (plain weave) in the range 40–85 by vol% were developed by impregnation technique followed by compression molding. These composites along with unfilled PEI were evaluated for their LAOW performance on SRV Optimol tester under different loads using ball-on-plate configuration. The performance was compared with that of composite evaluated in earlier work but developed with different processing technique (hand lay up). With increase in load, specific wear rates of all the composites increased while friction coefficient (μ) decreased. It was concluded that carbon fabric inclusion in all amounts proved significantly beneficial for improving friction and wear performance and limiting load of PEI. Very high and very low amount of CF (85 and 40 vol%) proved least beneficial from strength and tribo-performance point of view. Composites with moderate amount of CF (65 and 55 vol%) proved most promising with almost similar potential in reducing μ and wear rate of PEI. Overall CF in the range of 55–65 vol% appeared to be the optimum range for tailoring the strength properties along with tribo-performance in fretting wear mode. The impregnation technique proved significantly better than the hand lay up technique for enhancement in strength and tribo-performance. SEM studies on worn surface proved helpful in understanding wear mechanisms.

含硫化铜纳米粒子润滑脂的微动磨损性能研究

在微动磨损试验机上考察了含有硫化铜纳米粒子脲基脂的微动磨损性能。结果表明:硫化铜纳米粒子能显著降低微动磨损体积,随着纳米粒子含量增加,微动磨损量降低;在微动磨损后期纳米粒子的存在还能降低摩擦因数。低负荷下,润滑脂中硫化铜纳米粒子有利于降低微动磨损量;但在高负荷条件下,磨损量迅速增大,说明高负荷下微动磨损方式发生了变化。XPS分析表明,微动磨斑表面膜含有Cu、FeS等物质,说明硫化铜纳米粒子能显著降低微动磨损的原因在于纳米粒子化学性质非常活泼,在微动过程中容易与摩擦表面发生化学反应,形成具有保护性的沉积物膜和化学反应膜。     

ZM5镁合金微动磨损特性研究

采用高精度微动试验台研究了ZM5镁合金的微动磨损行为,法向载荷变化范围为50～200N、位移幅位为5～40μm。通过摩擦力-位移-循环次数变化分析,结合显微观测,结果表明:ZM5镁合金的微动磨损行为与微动区城特性密切相关。它的微动损伤形貌主要是磨损,在初期阶段的磨损机制主要是粘着和氧化,中后期是粘着、氧化和磨粒磨损共同作用的结果。     

A study of elastic-plastic buckling of cylindrical shells under torsion

The elastic-plastic buckling of cylindrical shells under torsion is analysed with a deep thick-shell model under various boundary conditions. The word ‘deep’ means that in the general equations of equilibrium the three non-linear terms that involve the torsional force are all retained for the buckling analysis. In the Donnell-type shallow-shell theory, however, only one of such terms is retained. The word ‘thick’ means that in calculating strains and stress resultants the factor (1+z/R) is retained. This factor results from the trapezoid-like shape of the cross-section and is usually neglected in the thin-shell theory. For boundary conditions, not only the conventional geometrical boundary conditions, which are in terms of displacements and rotations, but also the mechanical boundary conditions, which are in terms of forces and moments, are considered. The numerical results of examples assess the effect of the additional non-linear terms, the effect of the factor (1+z/R), and the effect of the mechanical boundary conditions.     

错层结构扭转及地震反应分析

以错层住宅为研究对象,讨论了错层对结构的影响.在水平地震作用下,错层区域结构受力变得非常复杂.文中,对该类结构引起扭转振动因数和扭转效应进行分析,同时提出该种结构的地震反应分析计算方法.